how to clean mass air flow sensor chevy equinox

This sensor will as time passes get dirty and its two filaments that will give information to your computer on the quality and temperature of the air will no longer be able to collect data correctly it is in this sense. Alright enough of the bs.

2018 2022 Chevrolet Equinox Maf Sensor Replacement Guide 016

Press the red clip slightly to unlock it.

. The most common signs of bad mass air flow sensor MAF in Chevy Equinox are loss of power or slow acceleration engine hesitation or jerking during acceleration erratic idling misfires poor exhaust emission values and sometimes black smoke comes out of the tailpipe. The intent of this cleaning will be to remove all its impure substances to allow it to work efficiently again. Mass air flow MAF sensors measure the amount of air entering the engine.

Now well proceed to the very delicate cleaning of the flow meter. Chevy equinox 2006 mass air flow sensor by delphi. Part 1 -how To Test The Gm Maf Sensor 31l 34l 43l 50l And 57l.

How to clean mass air flow sensor chevy equinox. Pull out the air flow sensor and clean it properly. MAF Sensor Cleaner on Amazon.

Remove the air mass sensor cleaner from its container and spray it on the sensor. Once off your MAF sensor should look like the one in the photo. Reliable and quiet your Chevrolet Equinox small crossover SUV is perfect for highway driving and it gets respectable gas mileage as well.

This automotive maintenance tutorial was specifically written to assist owners of the third generation 2018 2019 and probably also the face-lifted or revised 2020 2021 and 2022 model years GM Chevrolet Equinox SUV in cleaning or changing the MAF mass air flow sensor for the Ecotec 15 liter turbocharged four. The mass air flow sensor is part of the engines intake system and is. Remove the screw from the hose clamp and set it aside.

To clean your MAF sensor simply take a solvent and spray it onto a paper towel. Turn off the engine and let it cool down if youve been driving. Step 2 Remove the MAF sensor.

Tighten the screws so that they are snug. After that remove the sensor from the air cleaner housing with the help of the intake hose. One way to protect that fuel economy is with a new mass air flow sensor for Chevrolet Equinox from AutoZone.

Remove The MAF Sensor From Vehicle. Resetting the Mass Air Flow Sensor by Idling the Engine. Let soak the lower part of your mass air flow sensor not the plug part in acetone or another solvent for a few minutes which will take out most of the grime.

Let the cleaner sit for a few seconds afterward. Unplug the electrical connector from the mass airflow sensor. If you have a hot wire mass air flow sensor make sure the cleaner doesnt get onto the hot wires or plate.

Mass Air Flow Sensor. If you like you can also spray down the sensor with some WD-40. Here I demonstrate how I cleaned my manifold absolute pressure MAP sensor and mass air flow MAF sensor in 2012 Equinox with 24L ecotec engine.

Once taken apart you will be able to carry on to the step cleaning the mass air flow sensor of your Chevrolet HHR. Also clean the sides of the part its housing its connectors and its terminals. Remove the mass air flow sensor from the car or truck.

Httpsamznto2Wc7XESHow To Clean Mass Air Flow MAF Sensor in Chevrolet Colorado GMC Canyon Hummer H3In this video I am sh. Apply the cleaner 10-15 blasts around the inside of the sensor will do. The goal of this cleaning will be to take out all its impure substances to allow it to work efficiently again.

Two Screws On Side. Let soak the lower part of your mass air flow sensor not the plug part in acetone or another solvent for a few minutes which will remove most of the grime. Locate the mass airflow sensor near the engine air filter housing.

Remove the screws that hold the mass airflow sensor in place. Install the new MAF on your Chevrolet. This sensor will as time passes get dirty and its two filaments that will give information to your computer on the quality and temperature of the air will no longer be able to collect data accurately it is in this.

Now well proceed to the very delicate cleaning of the flow meter. If check engine light code p0171 persists after you have reconnected and replaced all damaged vacuum lines. The mass airflow sensor commonly abbreviated to MAF is one of the most important engine management sensors.

Pull the air inlet hose off the sensor and then pull the sensor off of the air filter housing. Once disassembled you will be able to carry on to the step cleaning the mass air flow sensor of your Chevrolet Trax. A bad mass airflow sensor can leave your Chevy Equinoxs engine running rough or even inoperable.

The Intake Air Temperature IAT sensor is also built into. If you need to replace it with a new one install the new sensor instead of the old MAF sensor. Step 3 Clean the MAF Sensor.

Place the sensor on a towel for cleaning. And lets get started with the actual step by step cleaning of the GM mass air flow MAF sensor Buick Chevrolet Oldsmobile Pontiac and GMC models. Clean your dirty mass air sensor.

Today I show you where your Mass Air Flow MAF Sensor is located and how to remove and clean it. There are two hose clamps on each side of the MAF sensor that hold it in place. Once it is dry it can be reinstalled and the car can be started again.

Then apply the solvent to the wire mesh on the front of the sensor and scrub in a circular motion with an emphasis on any oil residue that may be present. A MAF sensor measures the density of the air entering the intake manifold. 2018 Equinox Air Box.

It passes this information onto your Equinoxs ECU. Remove the connector with the harness of the sensor. Use a flat head screwdriver to loosen the hose clamp screws.

How To Clean Your Mass Air Flow Sensor Fixd Best Obd2 Scanner